View MC10E452_29371.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
5 Bit Differential Register
The MC10E/100E452 is a 5-bit differential register with differential data (inputs and outputs) and clock. The registers are triggered by a positive transition of the positive clock (CLK) input. A high on the Master Reset (MR) asynchronously resets all registers so that the Q outputs go LOW. The differential input structures are clamped so that the inputs of unused registers can be left open without upsetting the bias network of the device. The clamping action will assert the D and the CLK sides of the inputs. Because of the edge triggered flip-flop nature of the device simultaneously opening both the clock and data inputs will result in an output which reaches an unidentified but valid state. Note that the input clamps only operate when both inputs fall to 2.5V below VCC. The fully differential design of the device makes it ideal for very high frequency applications where a registered data path is necessary.
MC10E452 MC100E452
5-BIT DIFFERENTIAL REGISTER
* * * *
Differential D, CLK and Q; VBB Reference Available 1100MHz Min. Toggle Frequency Asynchronous Master Reset Extended 100E VEE Range of - 4.2V to - 5.46V Pinout: 28-Lead PLCC (Top View)
D3 25 MR CLK CLK VEE VBB D2 D2 26 27 28 1 2 3 4 5 D1 6 D1 7 D0 8 9 10 11 Q0 D2 D2 D Q Q2 Q2 D3 24 D4 23 D4 VCCO Q4 22 21 20 Q4 19 18 17 16 15 14 13 12 Q3 Q3 VCC Q2 Q2 Q1 Q1 D1 D1 D D0 D0 FN SUFFIX PLASTIC PACKAGE CASE 776-02
LOGIC DIAGRAM
D Q Q0 Q0
R Q Q1 Q1
R
D0 VCCO Q0
* All VCC and VCCO pins are tied together on the die.
R D3 D3 Q
D
Q3 Q3
R
PIN NAMES
Pin D[0:4], D[0:4] MR CLK, CLK VBB Q[0:4], Q[0:4]
12/93
Function Differential Data Inputs Master Reset Input Differential Clock Input VBB Reference Output Differential Data Outputs
D4 D4 CLK CLK MR VBB
D
Q
Q4 Q4
R
(c) Motorola, Inc. 1996
2-1
REV 2
MC10E452 MC100E452
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
-40C Symbol VBB Characteristic Output Reference Voltage 10E 100E Input HIGH Current Power Supply Current 10E 100E Common Mode Range -2.0 74 74 Min -1.43 -1.38 Typ Max -1.30 -1.26 150 Min -1.38 -1.38 0C Typ Max -1.27 -1.26 150 Min -1.35 -1.38 25C Typ Max -1.25 -1.26 150 Min -1.31 -1.38 85C Typ Max -1.19 -1.26 150 A mA 89 89 -0.4 -2.0 74 74 89 89 -0.4 -2.0 74 74 89 89 -0.4 -2.0 74 85 89 102 -0.4 V 1 Unit V Cond
IIH IEE
VCMR
1. VCMR is referenced to the most positive side of the differential input signal. Normal specified operation is obtained when the input signals are within the VCMR range and the input swing is greater than VPP.
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
-40C Symbol fMAX tPLH tPHL tS tH tRR tPW tskew VPP Characteristic Maximum Toggle Frequency Propagation Delay to Output CLK (Diff) CLK (SE) MR D D Min 1000 425 375 375 175 225 750 CLK MR 400 400 50 150 150 475 675 Typ 1400 600 600 625 -50 50 450 850 900 900 Max Min 1100 475 425 425 150 200 700 400 400 50 0C to 85C Typ 1400 600 600 625 -50 50 450 ps ps mV ps 1 2 20-80% 800 850 850 Max Unit MHz ps Condition
Setup Time Hold Time Reset Recovery Time Minimum Pulse Width Within-Device Skew Minimum Input Swing
ps ps
tr/tf Rise/Fall Times 250 475 725 275 1. Within-device skew is defined as identical transitions on similar paths through a device. 2. Minimum input swing for which AC parameters are guaranteed.
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E452 MC100E452
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E452 MC100E452
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E452/D*
MC10E452/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E452

	To Download MC10E452 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .